Kubota M96S/M108S Diesel Tractor

Engine
The M96S and the M108S are built with the power and durability to take on even the most heavy-duty tasks. This is due to their 4-valve, Electronic Center Direct Injection System engines, which help them realize greater pulling power.

"New" M108S Engine
The engine of the M108S has been redesigned and reengineered. Of course, it boasts the same durability and quality you've come to expect from Kubota E-CDIS diesel engines. But, this new turbocharged engine is now cleaner than ever before, offering higher torque and incredible pulling power. The CRS (Common Rail System) and Cooled EGR (Exhaust Gas Recirculation) System reduce emissions, helping with compliance to U.S. EPA Tier III emissions regulations. We've increased horsepower to 108 on the M108S and PTO power from 93 to 96 HP. These are big changes for a big tractor, and ones you'll certainly observe out in the field.

M96S Engine
Put the M96S into gear and you'll immediately see that this 95 horsepower engine will give you all the strength you need. You'll feel this in all applications, but you'll especially notice it when pulling heavy loads. The M96S's engine specs also boast a PTO output of 84 horsepower, low fuel consumption and it meets EPA Tier II emission regulations. Best of all, this engine comes standard with legendary Kubota reliability.

CRS (Common Rail System)
Typically found in automobiles to help reduce emissions and decrease fuel consumption, CRS has been implemented on our M108X engine to accomplish the same results. The CRS electronically controls the timing and amount of fuel injection. By delivering high-pressure injections in stages, rather than all at once, an optimal combustion rate is achieved, thus offering greater efficiency in the cylinder. This equates into less combustion noise, commonly known as "diesel knocks", better fuel efficiency and cleaner emissions. By controlling the amount of fuel injection, the CRS also serves to provide greater torque so that operations in the mid-to-high revolution range, such as baling, can be performed more smoothly.

Cooled EGR System
Our Cooled EGR (Exhaust Gas Recirculation) System aims at the same end as the CRS, to reduce noxious emissions. Specifically, the Cooled EGE System reduces smog-producing nitrogen oxides by lowering the combustion temperature. It accomplishes this by delivering exhaust gas through a cooler and then returning it to the combustion chambers, where the cooled gasses minimize temperatures and hamper nitrogen oxide formation.

Transmission

Swing Shift		Swing Shift Plus with Dual Speed
Our "Swing Shift" gives you access to a total of 16 speeds! The synchronized main shift's "H" pattern puts four speeds immediately at your disposal. The Swing Shift adds to that by actuating the electric-over-hydraulic high/low synchronized range shift for a total of eight speeds - all controlled by a single lever. If a task requires more than eight speeds, simply move the auxiliary range lever left of the seat for eight more to equal 16F/16R. An optional, simple-to-install, cassette-type creep provides eight additional slower speeds. That's 24 speeds - enough for the most demanding and precise work.		Swing Shift Plus models give you 32F/32R speeds, and allow you to operate the Swing Shift as well as the Dual Speed with just one lever. Should y our load suddenly get heavier, just push the Dial Speed's high/low button while still in motion. Your speed will reduce by 17%, but lugging force will dramatically increase. Put this feature to best use when taking on large load increases, when working in mixed soil or during hay tool applications. Combining the Dual Speed with the optional creep provides 16 additional slower speeds - a total of 48F/48R - for specialty applications. (Swing Shift Plus with Dual Speed not available on all models)

Hydraulic Shuttle Shift	Multiple Wet-disc Main Clutch	Hydrostatic Power Steering When performing tasks that place a heavy weight on the front wheels, such as loader work, our light-touch power steering helps make work much less strenuous. Heavy-duty Front Axle The M96S and M108S are equipped with the same rugged front axle found on larger tractors. So you can rest easy knowing that you can count on reliable performance, even when using the front loader.
Mounted on the left side of the steering column, the shuttle lever's fingertip control makes it possible to shift smoothly and easily from forward to reverse without using the clutch or stopping the tractor. This makes front loader operation significantly easier.	Our multiple wet-disc main clutch ensures smooth and effortless operation and offers grater durability.

Hydraulic Brakes
All it takes is a light touch to activate these highly responsive, hydraulic, wet-type brakes. This feature helps to reduce operator fatigue.

Extended Wheelbase
The extended wheelbase gives these tractors a lower center of gravity, directly equating to exceptional stability and pulling power.

Easy Step Tilt Steering Wheel		Easy to Sift 4WD Engagement
Find the position most comfortable for you. Step on the pedal, tilt the wheel to select from among five wheel positions, and then lock it in place. Simply step on the pedal again to unlock the wheel for easy tractor mounting and dismounting.		Stay moving and stay productive by switching the 4-wheel drive on and off without stopping, even when moving out of a field onto a road. (Do not engage while carrying heavy loads, or when a rear wheel has lost traction.)

Design, Comfort and Safety

Air Cleaner with Built-in Pre-cleaner	New Halogen Headlights with Corner Lamps	Instrument Panel with LCD Readout
This air cleaner will help protect your engine when operating your Kubota M96S or M108S in particularly dirty or dusty areas.	We've mounted the headlights high to improve visibility, even during loader work. These halogen lights with corner lamps are efficient and provide excellent illumination.	The new instrument panel makes viewing the vital functions of the tractor clear and easy. The LCD readout displays travel speed, PTO revolution and hour meter information digitally.

Foldable ROPS (ROPS model)
A Foldable Rollover Protective Structure (ROPS) is standard. It may be temporarily folded down without tools so that the tractor may pass under areas with height constraints, such as doorways or low branches. (There is no operator protection provided by the ROPS in the folded position. For operator safety, the ROPS should be placed in the upright and locked position and the seat belt fastened for all other operations.)

Extra-wide Operator Platform
The M96S and M108S boast a wide platform that offers more legroom for greater operator comfort.

Wrap Around Front Grill
The specially designed grill offers a wide coverage area, which helps to cool the engine better. At the same time, the grill design minimizes the overall air intake velocity, which reduces clogging of grass and dirt.

Slanted Full-open Hood
The slant-nosed, full-open hood design makes maintenance a snap, as the one-piece hood's dual gas shock assist enables it to lift up easily. This design feature also improves operator visibility over the center of the tractor hood for safer and more efficient working conditions. The curved design also provides a sleeker overall appearance.

Side-mounted Exhaust Pipe
The side-mounted exhaust pipe maximizes your field of view, allowing you to see more of what's in front and to the side of your work area.

Hydraulics and PTO

Floating Lift Rods
Floating lift rods are standard on the M96S and M108S. The rods offer a smoother ride and enhanced traction while using the 3-point hitch, especially on uneven terrain.
Heavy-duty Drawbar
This rugged and dependable drawbar, usually found on higher-end models, has the muscle it takes to tackle your toughest tasks, such as pulling heavy trailers.

3-point Hitch
The category II 3-point hitch provides fast and easy attachment of rear-mounted implements. The hitch's telescopic stabilizers and lower link ends make hook up and adjustments simple and worry-free

Independent PTO
The PTO clutch enables the implement drive system to engage smoothly, which helps reduce operator fatigue. And because the PTO is independent, you don't have to stop the tractor to engage or disengage the PTO, saving time no matter what the task.

Auxiliary Remote Control Valves
One remote valve (SCD) is standard on both the M96S and M108S. With the optional flow control valve installed, you can simultaneously operate the 3-point hitch and one remote valve, or two remote valves. Up to three remote valves can be installed in total.

CAB

Deluxe Suspension Seat
Our cab's deluxe suspension seat, with optional air ride suspension, is as comfortable as its name implies. This contoured, high-back seat is ergonomically designed to reduce fatigue, even after long workdays.

Corner-post Exhaust Pipe (Cab Model)
All of our cab models feature a corner-post exhaust pipe, which gives the operator an unobstructed field of view.

Front-opening Side Glass	High Quality Air Conditioner	Slide-out AC Condenser	Radio/Cassette/ CD Ready
The glass panels on the side of the tractor now open from the front, providing better interior air flow.	Our air conditioning system boasts nine air outlets, a dual-level air function and a stronger force of air - to keep you cool even on the hottest days	When they require cleaning, the sliding, louverless-type AC condenser and condenser net can be removed easily and quickly.	Speakers, antenna and wire harness are preinstalled for easy hookup.

New Front Loader

Protected Cylinder Tubes	Frame Design	Skid Steer-type Quick Coupler
To protect the tractor's hydraulics and offer the operator greater visibility, we've neatly tucked the hydraulic tubes inside the loader's boom. Hydraulic tube covers provide further protection from wear and tear.	The loader's thick steel frame has been simplified by removing braces and connectors. This redesign reduces the effort and time it takes to attach the loader and offers increased visibility.	A standard feature on the M96S and M108S loader, this coupler makes attaching and detaching buckets, bale spears and pallet forks as easy as can be.

More Capacity & Greater Height
We've increased the capacity and the maximum lift height of the loader to give you more power, reach and versatility. The loader's lifting capacity has been increased to a whopping 3,086 lbs. - perfect for heavy-duty bucket work. The loader's maximum height was raised to over 12ft, which will come in handy when using a pallet fork or bale spear.

Lifting Power and Height Adjustments
Two separate boom cylinder fulcrum points. )Power position and Height position) give you the option to increase the loader's lifting power or height based on your needs. When using the pallet fork or bale spear you may want to set the fulcrum to give you more height. For bucket work, a lower setting offers more power.

Joystick Control
The joystick offers you the ability to control the movement and speed of the loader with a single lever. The joystick tower also adjusts vertically, towards or away from the operator, and locks in place. This allows you to easily find your best working position. The Series Circuit makes simultaneous boom and bucket operation possible, while the Regenerative Bucket Dump Circuit enables quick dumping for efficient operation with quick cycle times.

4-bar Linkage
The 4-bar bucket linkage increases the rollback and dumping angle for quicker scooping and dumping.

Bucket Design
A recent design improvement in the loader bucket is its round back. This feature increases the durability of the bucket, helps keep wet materials from sticking in the corners and makes dumping sand and soil easier.

Quick-mount Attach/Detach
Attach or detach the front loader with ease and without the use of tools. Simply utilize the boom stand and mounting pins to quickly ready your tractor for its next job. A single-lever Hydraulic Quick Coupler (optional), available for the loader's hydraulic fittings, allows you to release all four lines at once.

Hydraulic Self-leveling Valve
This optional feature allows the operator to raise or lower the loader boom without changing the angle of the bucket. This will help prevent spills when carrying soil or sand and will make pallet handling smooth and easy.

Front Loader Options

Kubota Shockless Ride (KSR)	Single-lever Hydraulic Quick Coupler	3rd Function Valve
The KSR helps to minimize fatigue by "smoothing out" the ride of the tractor. This feature is particularly useful when your tasks include a lot of tight turns or lifting and dumping of heavy loads. It makes handling round bales far less jarring.	The optional quick coupler allows the operator to attach all four hoses at once. This makes attaching and detaching fast and easy, even when you're doing it often.	Operated with buttons located on the grip of the joystick, the 3rd function valve broadens the capability of the front loader. It also enables the simultaneous operation of the bucket and loader boom, allowing smooth and easy operation.

95 & 108 HP Mid-size Diesel Tractors	CAB Specifications
Cab and ROPS Models Available	ROPS Specifications
Cab and ROPS Models Available	Loader Specifications

FRONT LOADER	LA1403
Tractor Applications	M105S, M108S
Boom Cylinder Fulcrum	Height Position	Power Position
Maximum lift height to pivot pin	145.7 in	132.7 in
Clearance with attachment dump	112.6 in	98.0 in
Reach at maximum	23.6 in	38.6 in
Maximum dump angle	52�	63�
Reach with attachment on ground	87.8 in
Maximum rollback angle	40�
Digging depth (bucket level)	2.4 in	2.6 in
Overall height in carrying position	66.9 in
Material bucket width/capacity (heaped)	72 /19.43 in., 84/22.60 in.
Lift capacity bucket center	2976 lbs.	3086 lbs.
Raising time to full height w/out load	4.2 sec.
Lowering time w/out load	2.9 sec
Attachment Rollback time	2.2 sec
Attachment Dumping time	2.4 sec